# Outlines

> What each input in the syn.bike Outlines tab draws in the Bike view, and how to pick a shock model, shape the frame tubes and look up a fork.

An outline is the drawn shape of a bike's frame, fork, shock and other parts around its linkage. The **Bike** view draws your linkage inside a full bike: frame tubes, fork, shock, headset cups, stem and bar, saddle, seatpost and brake rotors. The outline is a drawing only. Nothing on this page changes a kinematic result.

![The Bike view showing a full suspension bike drawn as an outline, with the travel sliders underneath](https://syn.bike/images/docs/outline-bike-view-light.png)

No setup is needed. A bike with no outline settings is drawn with default tube sizes, a generic shock and a 200 mm rotor.

## The Outlines Tab

The **Outlines** tab in the left sidebar has four sections: **Components**, **Seatpost**, **Tube Dimensions** and **Pivot Diameters**. The **Seatpost** section has its own page, [Dropper Posts](https://syn.bike/docs/dropper-posts.md).

![The Outlines tab with the Components and Seatpost sections open](https://syn.bike/images/docs/outline-tab-light.png)

A value outside the allowed range is not applied. The field shows a message underneath and the drawing keeps the last valid value.

### Outline Components

| Field | What it controls |
|---|---|
| **Fork Travel:** | Fork travel in mm. It decides which fork is drawn and is the same value as **Fork Travel:** under **Fork and Shock Info** in the **Layout** tab. |
| **Shock Length:** and **Shock Ext. Length:** | Read-only here. Change them under **Fork and Shock Info**. |
| **Flip Shock Model:** | Swaps which end of the shock the body sits on. |
| **Mirror Shock Model:** | Mirrors the shock drawing about its own axis. |
| **Shock:** | The shock that is drawn, see [Shock Models](#shock-models). |
| **Rotor Size:** | `140`, `160`, `180`, `200` or `220` mm, used for both wheels. The default is `200`. |

The two shock toggles are also at the bottom of **Fork and Shock Info**.

### How the Fork Is Drawn

The fork is placed from **Fork Length** and **Fork Offset** in the **Geometry** tab. **Fork Travel:** picks the chassis:

| Fork travel | Fork drawn |
|---|---|
| Under 120 mm | 32 mm stanchions |
| 120 mm to under 140 mm | 34 mm stanchions |
| 140 mm to under 160 mm | 36 mm stanchions |
| 160 mm to under 200 mm | 38 mm stanchions |
| 200 mm and over | 38 mm dual crown |

A dual crown fork is drawn with a direct mount stem and no upper headset cup.

### Shock Models

**Shock:** starts on `Generic`, a plain body and shaft. The other choices:

| Brand | Model | Years |
|---|---|---|
| Fox | Float X2 | 2025–27 |
| Fox | Float X2 Parallel | 2025–27 |
| Fox | Float X | 2022–27 |
| Fox | Float X Neo | 2025–27 |
| Fox | DHX2 | 2025–27 |
| Fox | DHX2 | 2021–25 |
| Fox | DHX2 Parallel | 2025–27 |
| Fox | DHX | 2022–27 |
| Fox | DHX Neo | 2025–27 |
| RockShox | Vivid Coil | 2027 |
| RockShox | Vivid Air | 2024–26 |
| RockShox | Deluxe | 2023–26 |
| RockShox | Super Deluxe | 2023–26 |
| RockShox | Super Deluxe Coil | 2023–26 |

- The mount follows the shock length: 165, 185, 205 or 225 mm draws the trunnion version (mounted at the body end by a trunnion head instead of an eye), any other length the standard mount.
- The generic shock is drawn for a Parallel model on a trunnion length, and for any bike with **Uses Pull Shock:** turned on.
- If a model is drawn the wrong way around, turn it with **Flip Shock Model:** and **Mirror Shock Model:**.

### Headset Cups

The cups come from the **Geometry** tab: **Lower Headset Stack** and **Upper Headset Stack**, set per size. A stack of `0` draws no cup.

The stem, bar and saddle are drawn from the same table: **Stem Length**, **Stem Spacer**, **Bar Rise** and **Nominal Saddle Height**.

### Tube Dimensions

Each of the three main tubes has an outer diameter at both ends, in mm, and tapers between them. Each value must be above 0.

| Field | Default |
|---|---|
| **Top Tube Front:** | `35` |
| **Top Tube Rear:** | `35` |
| **Down Tube Front:** | `45` |
| **Down Tube Rear:** | `45` |
| **Seat Tube Bottom:** | `38` |
| **Seat Tube Top:** | `38` |

The seat tube stays at least 2 mm wider than the seatpost: 32.9 mm for a 30.9 post, 33.6 mm for 31.6 and 36.9 mm for 34.9. A smaller value is raised to that minimum, and so is a seat tube made too narrow by a larger **Seatpost Diameter:**.

### Pivot Diameters

Each drawn pivot has a diameter field in mm, named after the linkage point. The smallest value accepted is 10 mm.

An empty field uses the default, shown as grey placeholder text: 35 mm for the bottom bracket, 24 mm for a pivot where a link mounts on the frame, 20 mm for the other pivots (shock mounts included) and 14 mm for the ends of a DAQ sensor.

## Shape the Frame

Bend and move the top tube, down tube and seat tube directly on the plot. Round handles appear when the pointer is near the front triangle.

![The front triangle with a bend added to the top tube and its round handle showing](https://syn.bike/images/docs/outline-frame-handles-light.png)

| To do this | Do this |
|---|---|
| Add a bend to the top tube or down tube | Double-click the tube. Each tube takes up to 5 bends. |
| Move a bend | Drag its handle. |
| Remove a bend | Double-click its handle. |
| Move where the top tube meets the seat tube | Drag the handle at that joint. It slides along the seat tube. |
| Move where the top tube or down tube meets the head tube | Drag the handle at that joint. It slides along the head tube. |
| Change where the seat tube bends | Drag the handle on the seat tube. The tube keeps a straight run at the top for the seatpost. |
| Put a joint or the seat tube bend back | Double-click its handle. |

The down tube starts with one bend near the bottom bracket. Each change is its own undo step (`Ctrl+Z`). The shape belongs to the size on screen, so each size can be shaped separately.

## Look Up a Fork

The fork lookup fills in a fork's axle to crown length and offset from a list of production forks.

1. Open the **Geometry** tab and click the search icon at the end of the **Fork Length** row (**Look up a fork**). The expanded geometry table has the same icon.
2. In the **Fork Lookup** window choose **Brand**, **Model**, **Years**, **Wheel** and **Travel**.
3. If the fork was made with more than one offset, choose one under **Offset**.
4. Check the **Axle to Crown** value and click **Apply to All Sizes**.

![The Fork Lookup window with a brand, model, years, wheel size and travel chosen and the offset and axle to crown filled in](https://syn.bike/images/docs/outline-fork-lookup-light.png)

The brands listed are Cane Creek, EXT, Formula, Fox, Intend, Manitou, Marzocchi, Ohlins, RockShox and SR Suntour.

**Offset** depends on what the maker publishes for that fork:

- A single offset is shown as plain text.
- Several offsets become a list. While it reads **Pick an offset**, **Apply to All Sizes** stays disabled.
- Where no offset is published the row reads **Not published, left unchanged**, and applying changes the fork length only.

**Apply to All Sizes** writes **Fork Length** and **Fork Offset** to every size of the bike in one undo step.

> [!NOTE]
> The lookup does not change **Fork Travel:**. Set it yourself in the **Outlines** tab or under **Fork and Shock Info**, otherwise the fork is still drawn for the old travel.

## Sizes and What Is Saved

All of the outline settings are saved with the bike.

Shared by every size:

- Fork travel
- Shock model, **Flip Shock Model:** and **Mirror Shock Model:**
- Rotor size
- Tube dimensions
- Pivot diameters
- Seatpost diameter and dropper model

Set for each size:

- Tube bends
- Where the tubes meet the head tube and seat tube
- Where the seat tube bends
- Dropper travel, body length, exposed length and position

Everything else follows the geometry of the size on screen: wheel sizes, fork length and offset, headset stacks, stem, bar and saddle height. Change the size with **Switch Size** at the bottom of the **Geometry** tab or with **Frame Size:** in the drivetrain menu.

## Show and Hide Parts

Two buttons at the bottom right of the **Bike** view control what is drawn. The choices are saved with your account and apply to every bike you open.

- The gear-shaped button (**Show drivetrain settings**) has **Show Seatpost** and **Show Brake Rotors** under **Display:**. The rear rotor is drawn only when the largest cog is 36T or smaller. [Drivetrain](https://syn.bike/docs/drivetrain.md#the-drivetrain-in-the-bike-view) covers the rest of the menu.
- The plot settings button (**Show plot settings**) has **Wireframe Mode** under **Additional Display Settings:**, which replaces the outline with plain lines between the linkage points.
